Posts Tagged HA
Setting up EMC VNXe3150 iSCSI SAN Storage
Finally, the EMC VNXe3150 got installed and configured and almost ready to start transition from old EMC AX4 to the new VNXe3150. In the initial stage, found a bit difficulties to get it configured correctly as every EMC documentation speaks about something else specially when it comes to iSCSI High Availability, they mix between NFS HA and iSCSI HA. In reality, both Storage HA of NFS and iSCSI differ from each other. Simply, NFS uses Link Aggregations with LAG/LACP and iSCSI is not.
- VNXe 3150 with dual storage processors with software version 188.8.131.5232
- Two Dell Stackable 6224 – 24 port Gigabit switches configured with Jumbo frames for iSCSI and Flow Control Enabled.
- One – ESXi VMware ESXi 5.1.0 build-799733 host with 6 Gig pNIC’s two pNICs used for iSCSI connectivity only
Configuration on the VNXe
The configuration part is a bit of dilemma when it comes to iSCSI connectivity. In VNXe I set up two iSCSI Servers, one for Storage Processor A and one for Storage Processor B. Each SP has two IP Addresses configured for each Ethernet Interfaces, eth2 & eth3
All the Ethernet Interfaces are configured with 9000 mtu size for Jumbo Frame;
Storage Resources Configuration
|Storage Elements||iSCSI Server||Port||IP Address||MAC Address||pSwitch Port||VMKernel iSCSI PortGroup|
|iSCSI-A||iSCSI_ServerA||eth2||10.90.8.1||8:0:1b:57:71:3e||2/g1||iSCSI-01 10.90.8.78 vmk1|
|eth3||10.100.8.1||8:0:1b:82:78:dd||1/g1||iSCSI-02 10.100.8.78 vmk2|
|iSCSI-B||iSCSI_ServerB||eth2||10.90.8.2||8:0:1b:58:59:0f||2/g2||iSCSI-01 10.90.8.78 vmk1|
|eth3||10.100.8.2||8:0:1b:cd:f3:26||1/g2||iSCSI-02 10.100.8.78 vmk2|
As you can see in the above screen shot and configuration table, each storage process have two Ethernet ports, each Ethernet port is connected to iSCSI pSwitch, eth2 in SPA matched eth2 in SPB. So since both of these interfaces are connected to the same pSwitch and same IP subnet is configured on both, single iSCSI VMkernel PortGroup on the same subnet can reach to both Storage Processors through single physical adapter “vmnic”
VNXe Connectivity Diagram
iSCSI Switches Configuration
Both network switches are configured as master and slave stackable switches, basically for this type of configuration you will not require to stack the switches as each of pair SP Ethernet are connected to the same switch. i;e SPA-Eth2 in pSwitch1 & SPB-Eth2 in pSwitch1. But with NFS configuration you will require to stack the Switches as you will need to configure LAG/LACP for true High Availability
Set up Jumbo Frames on the two iSCSI gig switches so that all the ports are using support Jumbo Frames. Below commands will let you configure all the ports with mtu size 9000
Console(config)#Interface range ethernet all
ESXi host configuration
Each of the Gigs port in ESXi host is connected to the Physical iSCSI Switches. Two VMKernel PortGroups created in vSwitch1. Each of the iSCSI Kernels is mapped to the physical interface in ESXi.
Switch Name Num Ports Used Ports Configured Ports MTU Uplinks
vSwitch1 128 8 128 9000 vmnic2,vmnic6
PortGroup Name VLAN ID Used Ports Uplinks
iSCSI-02 0 1 vmnic6
iSCSI-01 0 1 vmnic2
vmk1 iSCSI-01 IPv4 10.90.8.78 255.255.255.0 10.90.8.255 00:50:56:6e:ea:87 9000 65535 true STA TIC
vmk2 iSCSI-02 IPv4 10.100.8.78 255.255.255.0 10.100.8.255 00:50:56:64:c0:6d 9000 65535
To check the connectivity is mapped correctly for each iSCSI PortGroup to reach the correct Ethernet Interface in the Storage Processor; vmkping with –I will allow you to specify the source interface to reach the destination iSCSI target; as this will test the whole path end-to-end from VNXe Storage, ESXi Hosts to Physical iSCSI Switches to make sure connectivity can flow with jumbo frame.
iSCSI Adapter Port Binding
Both iSCSI VMKernel portgroups has to be enabled for port bindings in the iSCSI Initiator adapter of ESXi.
# vmkping -I vmk1 10.90.8.1 -c 50 -s 9000
PING 10.90.8.1 (10.90.8.1): 9000 data bytes
9008 bytes from 10.90.8.1: icmp_seq=0 ttl=255 time=0.596 ms
9008 bytes from 10.90.8.1: icmp_seq=1 ttl=255 time=0.575 ms
9008 bytes from 10.90.8.1: icmp_seq=2 ttl=255 time=0.548 ms
— 10.90.8.1 ping statistics —
3 packets transmitted, 3 packets received, 0% packet loss
round-trip min/avg/max = 0.548/0.573/0.596 ms
# vmkping -I vmk1 10.90.8.2 -c 50 -s 9000
PING 10.90.8.2 (10.90.8.2): 9000 data bytes
9008 bytes from 10.90.8.2: icmp_seq=0 ttl=255 time=0.591 ms
9008 bytes from 10.90.8.2: icmp_seq=1 ttl=255 time=0.617 ms
9008 bytes from 10.90.8.2: icmp_seq=2 ttl=255 time=0.603 ms
# vmkping -I vmk2 10.100.8.1 -c 50 -s 9000
PING 10.100.8.1 (10.100.8.1): 9000 data bytes
9008 bytes from 10.100.8.1: icmp_seq=0 ttl=255 time=0.634 ms
9008 bytes from 10.100.8.1: icmp_seq=1 ttl=255 time=0.661 ms
9008 bytes from 10.100.8.1: icmp_seq=2 ttl=255 time=0.642 ms
— 10.100.8.1 ping statistics —
5 packets transmitted, 5 packets received, 0% packet loss
round-trip min/avg/max = 0.634/0.661/0.708 ms
# vmkping -I vmk2 10.100.8.2 -c 50 -s 9000
PING 10.100.8.2 (10.100.8.2): 9000 data bytes
9008 bytes from 10.100.8.2: icmp_seq=0 ttl=255 time=0.694 ms
9008 bytes from 10.100.8.2: icmp_seq=1 ttl=255 time=0.658 ms
9008 bytes from 10.100.8.2: icmp_seq=2 ttl=255 time=0.690 ms
Add ESXi hosts to VNXe
Setup the ESXi hosts to access VNXe iSCSI SAN Storage. This can be done by browsing into the VNXe > Hosts > VMWare will allow you to find ESX hosts either by typing in the IP Address of the vCenter or the management network of the ESXi itself. Then create VMFS datastore on the VNXe and make sure you are assigning permission to the ESXi host to access the newly created LUN.
After the LUN is presented to the ESXi host and formatted with VMFS now it’s time to change the path selection through from default Fixed to Round Robin and change the Round Robin default IOPS limit in ESXi from 1000 to 1 which will allow you to utilize all the iSCSI paths.
esxcli storage nmp psp roundrobin deviceconfig set –type=iops –iops 1 –device=naa.6006048c2fb691695617fc52e06065a2
Once it’s change you will see all the paths with Active(I/O) for each LUN that changed from Fixed to Round Robin.
Failover – Failback Testing Scenarios
For the failover testing I have presented 500 GB LUN and created two Virtual Machines, and installed Windows 2008 R2 Enterprise Edition. Roles installed on this guest machine;
- Microsoft Active Directory Role Services
- Microsoft DNS Server Services
- Exchange Server 2010 with all the Roles.
The second Virtual Machines are a Windows 7 Professional client with Microsoft Outlook 2010 connected to the Exchange 2010 MAPI profile. Sending and receive emails internally is operational in normal mode.
I have tested failover with network issues scenarios by disconnecting one pNic “vmnic2” from the vSwitch1 that mapped to iSCSI-01 portgroup and at the same time vmkping –I vmk1 was running against both VNXe iSCSI Target IP’s SPA-Eth1 “10.90.8.1” & SPB-Eth2 “10.90.8.2” and ping continues well. If a Storage Processor (SPA) fails/rebooted on VNXe, the working Storage Processor (SPB) picked up the workload that was handled by SPA.
- As you can see in the above screen shots, Virtual Machines Windows 7 Client continued pinging the Exchange Server and Exchange Server continued to ping Windows 7 Client.
- Vmk1 = iSCSI-01 which mapped to vmnic2 stopped pinging to the SPA-Eth2 & SPB-Eth2.
- LUN Paths both links mapped to vmnic2 subnet 10.90.8.x dead and 10.100.8.x paths mapped to vmnic6 ‘vmk2’ “iSCSI-02” are live and Active(I/O).
Ping “vmnic6” via vmk2 to 10.100.8.1 & 10.100.8.2
# vmkping -I vmk2 10.100.8.1
PING 10.100.8.1 (10.100.8.1): 56 data bytes
64 bytes from 10.100.8.1: icmp_seq=0 ttl=255 time=0.229 ms
64 bytes from 10.100.8.1: icmp_seq=1 ttl=255 time=0.192 ms
64 bytes from 10.100.8.1: icmp_seq=2 ttl=255 time=0.238 ms
— 10.100.8.1 ping statistics —
3 packets transmitted, 3 packets received, 0% packet loss
round-trip min/avg/max = 0.192/0.220/0.238 ms
~ # vmkping -I vmk2 10.100.8.2
PING 10.100.8.2 (10.100.8.2): 56 data bytes
64 bytes from 10.100.8.2: icmp_seq=0 ttl=255 time=0.235 ms
64 bytes from 10.100.8.2: icmp_seq=1 ttl=255 time=0.245 ms
— 10.100.8.2 ping statistics —
2 packets transmitted, 2 packets received, 0% packet loss
round-trip min/avg/max = 0.235/0.240/0.245 ms
Relink vmnic2 to vSwitch1 and ping resumed back to SPA-Eth2 & SPB-Eth2
LUN paths resumed
Testing Power Failure of VNXe Storage Processors-A & Storage Processor-B
The second test was done by removing the physical power from Storage Processor-B and initiate vmkping to both Ethernet Interface of SPB from both VMKernel vmk1 & vmk2, as a result vmkping continues as the traffic routed peer SP port.
Result of ping after
Below result shows that Exchange VM continues to ping the Client VM during Storage Processor-B shutdown.
Did the same with Storage Processor-A and initiated ping to both Ethernet Interfaces of SPA. Ping continues to both Ethernet Interfaces as well as pings inside each VM “Exchange Server to Client” and vice versa continues as well and Exchange Server VM didn’t give any freeze / errors in event viewer.
The VNXe3150 high availability feature at storage level and networking level ensures data protection against any single component failure in Storage Level and Networking Level.